DPS a doppia tecnologia - http://www.gps-standard.com/en

IT | EN | FR
Go to content

DPS a doppia tecnologia

Solutions > Perimeter protections > Invisible protections
DPS – Dual-technology System
Analizzatore Interrato
HOW IT WORKS
Volume change in the generated electromagnetic field and pressure changes in the surface area caused by walking, running, jumping, driving etc.

LOCATION
In all surface areas and underneath sand, grass, pebbles, paving, asphalt etc.

LENGHT
From 20m to 200m (Stand Alone) / 12.8 Km (Multiplex). The detection strip is about 1.5 to 3.0 metres wide.

ALARM ZONES
A maximum of 2 zones (Stand Alone), 20 zones for 200m (Multiplex).

ADVANTAGES
Invisible, and combines the advantages of the active RPS and the passive GPS detection systems. DPS has the highest detection rate and the lowest FAR (False Alarm Rate).
OVERVIEW
DPS®, Dual-Technology Perimeter System, is a dual-technology system created by the combination of two invisible systems: “GPS® PLUS”, detecting pressure difference, and ”RFC™” detecting changes in an electromagnetic field. Using a DSP microprocessor, DPS allows the processing of a large number of signals received in a very short time.
The changes in pressure and electromagnetic field generate signals that, properly processed and analysed, allow the correct determination of system alarm conditions. The alarm signals obtained this way are then sent to the control centre.
The system is modular and allows protection of extended perimeters. It can generate the alarm event when the signal comes separately from the two technologies (OR), or only when the detection comes from both sensors (AND).

VERSIONS
DPS® is available as a Stand-Alone version, for maximum protection of 200 mt, and in Multiplex version, for maximum protection of 12.8 Km, with a single perimeter control unit (MIND™). The architecture allows interconnection of up to 64 MIND units.

OPERATION
DPS® is based on two different technologies: GPS® Plus and RFC™, enhancing their main characteristics. GPS® Plus is based on the detection of the difference in pressure generated by people or objects on the ground, passing over the sensitive area. RFC™ detects changes in the electromagnetic field generated by people or objects crossing the sensitive area; it then makes a comparison between the radiofrequency energy that is transmitted and received.

The signals obtained from two sensors are sent to the analyser, that analyzes and transmits warning or alarm signals to the control unit. Crossing of the sensitive strip generates a significant change of pressure in the tubes, which is detected by an appropriate transducer. It also generates a change of the electromagnetic field, which is detected by the RCF™ system Mixer.

The signals thus obtained are analysed by the DSP and translated into warning or alarm signals. The possibility to calibrate the sensitivity of each leg allows the system to adapt to the particular characteristics required for each installation.

CHARACTERISTICS
- Signal processing in the time domain.
- Signal processing in the frequency domain.
- Combined frequency-time processing.
- Use of masks to characterize and recognize signals sent by sensors.
- Detection of signal energy levels (spectrum analysis).
- Listing per category of signal energy matrixes.
- 8 local inputs and 8 relay outputs available (optional).
- Local recording, selfcalibration.


     

     

About GPS Standard | Ethics | Green Policy | Contact Us | Work with us | Privacy | Cookie Policy | Sitemap | (+39) 0125-968611 | info@gps-standard.com

     

About GPS Standard | Ethics | Green Policy | Contact Us | Work with us | Privacy | Cookie Policy | Sitemap | (+39) 0125-968611 | info@gps-standard.com

P.IVA IT00473450070 | Cod.Fiscale e num. Iscrizione Reg. Impr. Aosta n.00473450070 | REA Aosta n.43618 |


P.IVA IT00473450070 | Cod.Fiscale e num. Iscrizione Reg. Impr. Aosta n.00473450070 | REA Aosta n.43618 |
Back to content